series am epr8d - az up to 0.7a | a c - dc led d river www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3 . h 1 of 4 north america only features: models single output model max output power (w) output voltage range (v) no load output voltage (v max.) output current (a) input voltage (vac/hz) efficiency (%) 115 vac 230 vac amepr8d - 2435 az 8.4 1 2 - 24 34 0. 35 90 - 2 64 /47 - 440 79 80 amepr8d - 184 0 az 7.2 9 - 18 20 0.4 90 - 2 64 /47 - 440 77 79 amepr 8 d - 12 7 0az 8.4 6 - 12 15 0.7 90 - 264/47 - 440 75 7 8 * exceeding the maximum output power will permanently damage the converter . note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. amepr 8d - az?s ac/dc led drivers have electrical safeguards designed within to protect it from conven tional electrical abnormalities with the levels listed in the safety table. applications for use within rural agricultural, heavy industrial, and other areas or regions which are prone to ?dirty? electrical conditions which would subject any of the above models to excessive voltages surges or spikes, may damage or cause early life failure of product. in this case consideration should be made by the end user to ensure that adequate line o r mains surge suppression is installed in front of aimtec device to en sure the longevity of the products. failure to identify excessive line surges violations prior to installation may damage sensitive equipment permanently. i nput specifications parameters conditions typical maximum units current (full load) 115 vac 85 ma 230 vac 5 0 ma inrush current <2ms (cold start) 115 vac 10 a 230 vac 5 a leakage current 230 vac 0. 02 ma power f actor 115 vac (full load) 0.9 8 230 vac (full load) 0.9 5 external fuse recommended slow blow type 1 a start - up time 100 ms output specifications parameters conditions typical maximum units current accuracy 1 5 % line regulation ( ll - hl ) 0.5 % load regulation min. - m ax. load 5 % ripple & noise * 1.6 v p - p hold - up time 28 m s minimum l oad v oltage see the models table maximum capacitive load 200 f * ripple and noise are measured at 20mhz bandwidth by using a 0.1f (m/c) or (c/c) and 220 f (e/c) parallel capacitor. ? ac - dc constant c urrent led driver ? class 2 power supply ? input r ange 90 - 2 64 vac/47 - 440hz ? active pfc ? high efficiency up to 80 % ? operating t emperature - 20 to 85 c ? total harmonic distortion < 20% ? scp, over load protection ? leading or trailing edge triac ? ip67 case click on series name for product info on aimtec.com
series am epr8d - az up to 0.7a | a c - dc led d river www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3 . h 2 of 4 north america only isolation specifications parameters conditions typical maximum units tested i/o voltage 3sec 3000 v ac isolation r esistance >1000 m general specifications parameters conditions typical maximum units switching frequency 66 khz over load protection R 1 10 % over voltage protection R 1 10 % short circuit protection auto recovery operating temperature with derating over 75 c refer to model application o c storage temperature - 40 to +95 o c maximum case temperature 100 o c temperature coefficient 0.02 % / o c cooling free air convection humidity non condensing 20~ 95 % rh case material plastic potting epoxy (ip67 rated) wires ul1015 input 18awg*10cm / output 20 awg * 1 0cm weight 55 g dimensions (d x l ) 2 7 . 4 x 70 .3 mm ( 1. 0 8 x 2.77 inch es ) mtbf >400,000 hrs (mil - hdbk - 217f at +25c) environment approval test parameters conditions shock wave form half sine wave acceleration amplitude 5gn bump duration 30ms converter operation before and after test, body mounted (on chassis) number of bumps 18 (3 in each direction for every axis) vibration test mode sweep sine, 10 - 100hz, speed 0.05hz/s displacement 1 mm acceleration 3g, 3 loops 30min one cycle, 3h total, every axis tested converter operation before and after test, body mounted (on chassis) safety specifications parameters agency approvals culus, fcc standards ul8750, ul60950 - 1, class 2 power supply per ul1310 , fcc 15 , wire specification s wire parameters color input acn blue acl brown output + v output red - v output black
series am epr8d - az up to 0.7a | a c - dc led d river www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3 . h 3 of 4 north america only dimensions derating - 20 0 20 40 60 80 100 100 80 60 40 20 0 75 o c safe operating area - 25 85 free air convection ambient temperature o c
series am epr8d - az up to 0.7a | a c - dc led d river www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3 . h 4 of 4 north america only triac dimming feature note: 1. datasheets are updated as needed and as such, specifications are subject to change without notice. once printed or downloaded, datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels sho wn, including s afety age ncy certificatio ns o n labels, may vary based o n the date manufactured. 3. mechanical drawings and specifications are for reference only. 4 . all specifications are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. .aimtec may not hav e conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other li mited information are considered proprietary and may not be available for release. 5. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control s ystems or other suc h applic atio ns whic h necessitate specific safety and regulatory standards other the ones listed in this datasheet.
|
